Hallo,Ik zou graag mijn d-link (DIR-636L) achter mijn telenet modem aan wullen sluiten maar krijg het niet klaar gespeeld. In de handleiding staat het volgende:If you are connecting the DIR-636L router to an existing router to use as a wireless access point and/or switch, you will haveto do the following to the DIR-636L before connecting it to your network:.Disable UPnP.Disable DHCP.Change the LAN IP address to an available address on your network. The LAN ports on the router cannot accepta DHCP address from your other router.Die UPnP heb ik al kunnen uitvinken in m'n configuratie van m'n d-link maar die andere 2 vind ik niet/weet ik niet hoe ik dat doe.Moet ik dan een soort nieuw ip adres aanmaken of wat moet ik daar doen? En ook, de kabel die van de telenet modem naar de d-link gaat, waar moet die worden aangesloten?Hier in de link zie je de aansluitingen van de d-link.Alvast bedankt op voorhand.Mvg. Dit staat er in de handleiding:Connect to an Existing RouterIf you are connecting the DIR-636L router to an existing router to use as a wireless access point and/or switch, you will have to do the following to the DIR-636L before connecting it to your network:. Disable UPnPTM. Disable DHCP.
Telenet Wifi Router Versterken Password
Change the LAN IP address to an available address on your network. The LAN ports on the router cannot accepta DHCP address from your other router.To connect to another router, please follow the steps below:1. Plug the power into the router. Connect one of your computers to the router (LAN port) using an Ethernet cable. Make sure your IP address on the computer is 192.168.0.xxx (where xxx is between 2 and 254).
Please see the Networking.Basics section for more information. If you need to change the settings, write down your existing settings before making any changes. In most cases, your computer should be set to receive an IP address automatically in which case you will not have to do anything to your computer.2. Open a web browser, enter and press Enter. When the login window appears, set the user name to Admin and leave the password box empty.
Click Log.In to continue.3. Click on Advanced and then click Advanced.Network. Uncheck the Enable.UPnP checkbox.
Click Save.Settings to continue. Click Setup and then click Network.Settings. Uncheck the Enable.DHCP.Server checkbox. Click Save.Settings to continue.D-Link DIR-636L User Manual 11Section 2 - Installation5. Under Router Settings, enter an available IP address and the subnet mask of your network. Click Save.Settings to save your settings.
Use this new IP address to access the configuration utility of the router in the future. Close the browser and change your computer’s IP settings back to the original values as in Step 1.6.
Disconnect the Ethernet cable from the router and reconnect your computer to your network.7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router.
Do not plug anything into the Internet (WAN) port of the D-Link router.8. You may now use the other 3 LAN ports to connect other Ethernet devices and computers.
To configure your wireless network, open a web browser and enter the IP address you assigned to the router. Refer to the Configuration and Wireless Security sections for more information on setting up your wireless network. Je moet kijken welke IP adressen in jouw interne netwerk gebruikt worden.
Meestal is dat 192.168.1.X of 192.168.0.X. Je moet wel zeker zijn welke van de twee.
Kijk even welk IP adres je computer heeft. Dan weet je of het met een 0 of 1 moet zijn.Dan geef je daar bijvoorbeeld 192.168.0.2 in als je in die range zit, want 192.168.0.1 is dan in principe de router van Telenet, dat IP adres mag je niet kiezen.Subnet mask laat je zo staan: 255.255.255.0Opgelet: vanaf dat moment moet je bevestigen. Daarna misschien even de router herstarten. Vanaf dat moment kan je alleen maar in de router met het NIEUWE IP adres.
Idd, en als ik er een extra utp kabel insteek om mijn ps4 en cloudstation aan te sluiten doen die 2 extra utp's niets. Krijg er geen verbinding door. Enkel op die 1ste utp kabel naar m'n pc Ik word er een beetje horendol van. Heb net ook eens geprobeert met zo'n goedkope switch van 10 jaar terug ofzo en dan haal ik deze snelheden maar ook enkel op die 1ste kabel, kabel 2 en 3 geven m'n toestellen aan dat ze geen signaal hebbebEn die switch is normaal geen gigabit model, maar een 100 Mbps en toch haal ik deze snelheden Ik ga een paar uurtjes de pc opzij zetten en wat tv zien enz, m'n geest verlichten.
This article will provide some general router (or modem router) setup advice which may help you set up a third-party router or modem router for iiNet NBN™ Wireless broadband.If your modem router was purchased from iiNet, you'll find its setup guide in.Select one of the links below to jump to a query:.What you'll need. An active NBN™ Wireless broadband service. We'll send you an SMS and/or email when your broadband service is activated. A WiFi router or NBN™-ready modem router.Important: The router should feature at least 802.11n or 802.11ac WiFi. Not all are created equal, and devices manufactured before 2009 may only feature the older 802.11g or b signals which may not support the speed capability of your NBN™ service.Similarly, older devices may simply be 'modems' and not 'modem routers', which means it doesn't have the ability to wirelessly broadcast your internet as a WiFi signal in your home.
These days the vast majority of modems on the market are actually modem routers by default, and we just call them modems because that's the norm. If your modem doesn't have a WiFi feature, you'll need to purchase a WiFi router to use instead. The power supply cable that came with your router.
If you need a replacement for any reason, take care to note the Rated Input on the router's barcode sticker (e.g. 12V/2A) and buy a matching cable. An Ethernet cable (at least one is typically included with a router, usually a Cat 5e). There are of Ethernet cables. If you're purchasing one from a store, we recommend Cat 6 or Cat 5e. A Cat 5 cable is not recommended because it may not support the speed capability of your NBN™ service. Optional to connect additional computer(s) to your router via Ethernet: Additional Ethernet cable(s).
Optional if your home has Hub/Smart internal Ethernet wiring: Another Ethernet cable. This will allow you to connect your NBN™ Connection Box to a port on the nearby patch panel, and then plug your router into the corresponding port on a patch panel in another room.Plugging in and connecting computers. Find the indoor NBN™ equipment in your home - this will be a Connection Box that's plugged in to an electrical outlet and the wall socket for your NBN™ Wireless antenna. You'll also need another available electric outlet to give your router power. If you need to use a double-adapter, power board or extension cord this should be okay, but if your router ever seems to have power issues the first thing you should try is plugging the power supply cable directly into the electrical outlet on the wall. Take your router's power supply cable and use it to connect your router's power port (example below) to an electrical outlet.
You may turn the router on now or wait until you've finished plugging in the other cables. Take your Ethernet cable (this is typically blue, yellow or grey but other colours are possible) and plug one end into the active UNI-D port on your NBN™ Connection Box. In most cases, the active port will be UNI-D 1 as shown below. If a different UNI-D port was activated when your NBN™ equipment was installed, please use that one instead.If you don't know which port is the active one, please call us on 13 22 58 and we can check our records. Optional: If your home has internal Ethernet wiring (sometimes called Smart or Hub wiring) then you may plug the other end of the Ethernet cable into a port of the nearby patch panel.